www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 1 of 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 110n smd - 3 m arking ? hdf101 prepared checked approve d ? d a t e 200 6 - 5 - 11 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 2 of 9 ?? history record date spec . no . ?? part no . ??? customer no . mod ify content ? remark
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 3 of 9 1. scop this specification shall cover the characteristics of saw filter with f110ns3 used for the page system. 2. electrical specification dc voltage vdc 10v ac voltage vpp 10v50hz/60hz operation temperature - 4 0 to + 85 storage temperature - 45 to +85 rf power dissipation 0dbm 2.2 electronic characteristics ? part number hdf110n ? (fo)(mhz) nominal center frequency 110.592 3db bandwidth(from fo)(khz) +/ - 576min ? stop band attenuation (from peak level)(db) 1)fo - 5.0mhz 2)fo - 3.5m hz 3)fo+/ - 1.728 mhz 5)fo+3. 456 mhz 6)fo+5mhz 50min 45min 30min 40min 40min (db) insertion loss(at minimum loss point) 4.5max ?? ( fo+/ - 576khz)( sce.) group delay deviation 0. 7 / input/output impedance 300 //1.2 h
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 4 of 9 3.dimension marking hdf 101 hd: brand f : filter 101 : no. 4.test circuit 3.input /output 2. input or input ground 1.5. to be ground 6.output or output ground 4 .8. case ground 7. output /input
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 5 of 9 5 5 . . t t y y p p i i c c a a l l f f r r e e q q u u e e n n c c y y r r e e s s p p o o n n s s e e 5. environmental characteristics 5 - 1 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 2.2 . 5 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 2.2 . 5 - 3 solderability submerge the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in 2.2 . 5 - 4 mechanical shock drop the device randomly onto the co ncrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2.2 . 5 - 5 vibration
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 6 of 9 subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill th e specifications in 2.2 . 6. remark 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be soldered. please avoid soldering another part of component. 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) ree l: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structure (1) the tape shall be wound around the reel in the direction shown below.
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 7 of 9 (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications. 8. tape specifications 8.1 tensile strength of carrier tape: 4.4n/mm width 8.2 top co ver tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 8 of 9 [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.0 0.3 5.5 0.05 1.75 0.1 4.0 0.1 8.0 0.1 2.0 0. 05 ? 1.5 0.1 ? 1.0 0.25 0.3 0.05 2.10 0.1 6.40 0.1 5.20 0.1 [figure 2] [unit:mm] a b c d e w t r ? 330 ? 100 ? 13 ? 21 2 13 3 1.0
saw filter hdf 110n s md - 3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail : info@shoulder.cn page 9 of 9 1.0 0.5 0.5 0.8 0.5 0.3 max. max.
|
